Hp Inkjet Printer Ink, Hp Inkjet 4100 Ink, Hp Driver 94 96

Hp Inkjet Printer Ink, Hp Inkjet 4100 Ink, Hp Driver 94 96

readmore..

HP OfficeJet 7110

The scanner hardware is used every time a fax is sent.

Although its not a guaranteed fix, try cleaning the underside of the scanner glass giving particular attention to the white strip on the right. If that fails the scanner module is probably the problem.

General
The Automatic Document Feeder (ADF) will need to be removed before the glass can be removed. You will also need a T10 Torx head driver approximately 6" long. Driver handles that accept removable bits may be too large in diameter for this particular job.

Removing the ADF
1. Hinge the ADF upward as if you are going to manually scan a document.
2. In the hinge area there is two black pull latches. Pull them up and lift the ADF straight up to remove it. It may take some side to side rocking before it will disengage.

Removing the Scanner Glass
1. Remove the four T10 Torx head screws around the perimeter of glass, i.e. two in the ADF hinge area and one on the right and left.
2. Remove the Control Panel overlay. It pries off.
3. Open the printer as if you are going to access the cartridges and disengage the support legs. Two latches at the base of each leg must be pried outward with a slot style screwdriver to disconnect them. The scanner assembly will now "flop" freely, so steady it while removing the four screws on the underside.

Note: The screw in the front is hidden under the piece that you grasp to gain cartridge access. Two latches must be released to remove it. The screw can now be seen using a flashlight but may be obscured by some wires.

readmore..

HP OfficeJet 7110 Series

I like to repair as much as I can for my customers. It is indeed a lot of work tot clean al the components and make them working again. But if you know how to open up the machines it will make the whole operations a lot easier. And every year the machine is running it’s cheaper.

Preventive cleaning once a year will make the lifecycle of the machine a lot longer.

Kind regards,

Henri.

readmore..

Samsung SCX -4300 error

It must be "1.13fix" not "1.13"! Let's start again. To solve problem you need to download PATCHED by scx4300.exe 1.13 firmware where additional reset procedure was implemented in.

To patch firmware you need to unpack archive in any folder then open commad line interface go to this folder then type "fix4300.exe SCX4300_V1.13_Fact_romdl.hd". If no error occurs you will find file "FIX_SCX4300_V1.13_Fact_romdl.hd". It's a patched firmware. The next step is to download this file to printer.

Enter TECH mode, activate download by "Menu > Data Setup > Flash Upgrade > Local [OK]" then type in command line "usbprns2.exe FIX_SCX4300_V1.13_Fact_romdl.hd" to start download. During download printer displays:
Data receiving > Flash erasing > Flash Programming > Checksumming > Download Ok then printer will restart. It's all.

To reset all counters and unblock printer enter Tech mode go Data Setup > Clear counters. In this menu you will find "Clear All CNT" instead of "Total Page CNT". Choose "Clear All CNT" then press [OK]. Printer will display "warming up" and LED will yellow for seconds then change to green.

After reset all counters in report will be zero and toner 100%. You may repeat this procedure as soon as you need.

download software

readmore..

Driver HP, HP 2210PSC,

You can follow these steps to resolve the issue.
How to clean without removing the bulb:

Take off the hood.

At the back side, on top behind the window, are two round holes. With a small screwdriver you can take out the two screws.
Lift the back side of the window and at the same time click the front loose (first left then right).

The window can fully be taken off by disconnecting the wire (there is a plug at the rear side of the window on the right side).

On top of the bulb and mirrors there is a black cap, you can remove it by putting a small screwdriver in the two square holes
(one at a time) and pull the screwdriver to the right, the cap clicks off.

Now you can see the mirrors and the back side of the bulb (at the back side there is a wire). Clean the mirrors and the front side of the bulb using a wet cloth (with your small finger you can clean the front side of the bulb, that looks down).
You don't need to remove the bulb!

readmore..

HP 2210PSC

Scanner failure...turn power off than on...ALL four lights, COPY, FAX, SCAN, and PHOTOCARD blink continously...

Every time the printer gets turned on and goes throught the initalization process it makes the loud noise as the scanner bulb attempts to make a pass accross but fails...never even needed to scan anything.

Proceeded to buy new printer for the house for the wife and kids to use....Now starting a new business so dug it out from the basement, connected it to my computer with the software loaded and still it does not work. Has the same exact issues...Read all the suggestions...Want to remove the strip under the bulb as suggested, but dont know how to get at the bulb. Do you need a special tool?? Does this end the nightmares for good??

Can this unit be salvaged or am I better off just buying a newer model and be done with it??

readmore..

HP PSC 2210

I have an HP PSC 2210, it prints, faxes and manages to copy but when it comes to scan this comes up: "Error: An error occurred communicating with the scanning device. Please ensure the scanning device is connected properly and try again." I have tried tis countless times with no success, there's one cable to the All in one and every other function works. Help
___________________________________________________

I had the same problem for months until today I decided to fix it for once and all. I uninstalled the software on the computer. I downloaded the utility from HP's Website to do a 100% uninstall. I then downloaded the driver 2.1.0 from HP's website and didn't use the CD for the re-installation. Here is the website:

For WinXP: http://h10025.www1.hp.com

The Driver - HP Full Solution Software Driver - 166.14 MB
Cleaner - Software Cleanup Utility - 2.04 MB

When you run the cleaner, open it from where it extracts to (defaults for me was C:\HPAiOScrubber) and run the file OjScrubber.exe and press the plus for the 2200 scanner and uninstall both of those. I don’t know if it's necessary but I uninstalled everything on that list.

So again;
1. Uninstall Software from PC (Control Panel).
2. After the forced restart run the Cleaner.
3. Install the driver you downloaded (166.14 MB).

When you install the driver keep the USB wire disconnected until it tells you to plug it in and after you put it in it should take 5min (mouse will freeze, don’t worry) then it should show a green check mark, and it will continue the installation.

I did that and it worked for me.

Later.

readmore..

HP PSC 750

I have an HP PSC 750,
and I too am getting the same old "Scanner Failure. So Please shut it down and then unplug it.
Well I do not have a re-fresh button like some of those guys say for me to do!
So this is what I found that has worked for me and hopefully for you all.
1. Turn off your printer and then UNPLUG IT!
let it sit for at least 5 minutes then repulg it. (if you do
not need it I sometimes leave it unplug overnight and replug it the very next morning).
This will help it to go into the refresh mode.
2. What is happening here is there is a memory set problem here.
What this printer needs for it to be RE-SET!
This is why we need to un plug it from time to time.

You see when you leave this printer on, it goes into a scanner memory by default 9 Why I do not know but this is my belief!), and when you all try to copy it does not want to go into this copy mode.
By unplugging it and replugging it this will re-set your printer to where it is like it should be.

Now if you are an electrician, you can put an on and off switch on this cord where it is easier for you to reach if your cord is too far buried for you to reach.

And if you are not an electrician...... Please get some help from someone who knows what they are doing and what you are going to do with this powercord for your printer. PLEASE!

NOTE: YOU MAY NEED TO ( UN PLUG AND REPLUG ) THIS MORE THAN ONCE, BECAUSE OF THE STUBBORNESS THAT YOUR PRINTER IS IN AT THAT TIME.

If you need any more help then you can e-mail me at "Maverick2842@sbcglobal.net"

Eddie

readmore..

Scanner error keeps coming up

I had this problem develop yesterday after 2 1/2 years of good service from this machine.

I found this fix

http://forums1.itrc.hp.com

Opening up the scanner and removing the large black plastic flap covering the scanner mechanism restored it to full working order.

Why I have no idea? Maybe the cover shifts and covers a sensor or receptor?

I was on the verge of running out and buying another machine!

readmore..

service anon S750

Can't guarantee this will work, BUT don't deviate from this procedure. This worked on my Canon s630. Taking the printer apart is not that easy, you must work on the basis that the printer will be write off before start stripping it down.

Waste Ink Tank Full Error Reset

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button 1 more time.
8. Done.

readmore..

Canon S750

Great site, hope I can find some help. My fairly old Canon S750 started acting up by banding and poor print quality. After replacing all the ink I am unable to get it to print at all. The lights were flashing orange 7 times then green once. Attempted resettting ink waste tanks following some instructions I found on this site but now printer flashes orange followed by green 7 times then once green. Any help folks? Thanks

I have error message on my S750 printer alternate green and orange and then a long green and repeats. Have you found out what the problem is or the sequence to reset it? If so I would like to know the problem or the solution. With my printer it will not shut off either.

readmore..

Datamax M-class - turning off

I have a customer that has a Datamax m-4206 that will be working fine and then it just turns off. They have to switch it off for about 5 seconds and turn if back on. It will run for about and hour or so and then start turning off again. Is this the power supply or something else.

Thanks

readmore..

HP Officejet K60 Alignment Failed /no yellow color

The printer must be able print yellow in order to execute the alignment. Part of the alignment process involves scanning printed yellow bars. See the web page below for a sample of the printout. I suggest that you clean the carriage and cartridge electrical contacts with a cotton swab moistened with water. If you still fail to get yellow, test the cartridge in another printer. Any Deskjet 900 series will accept the cartridge.
http://h20015.www2.hp.com/en/document.jhtml?lc=en&docName=bpu00657

readmore..